![]() ![]() If all days of the week are not flashing, carefully scroll through the days until all days are flashing in unison. On the bottom of the display you'll see the days of the week flashing. Be sure that the screen also reads ON in the top left corner. Turn the round dial to scroll through until the screen reads DUSK. You will now see SKIP blinking on the screen. Press the PROG button once to select event 1 for programming. You will now see the number 1 flashing on the display. If you're looking at your timer's clock, press the PROG (program) button once. Programming your timers On / Off times can be tricky the first time, so go slowly and take your time. Some people prefer their lights to remain powered on from dusk to dawn, while others prefer dusk to midnight. Now that your time, date and location are entered into the timer, you're now ready to begin programming the ON/OFF times for your lights.įirst, consider how you would like your lights to operate. Your initial programming for time, date and location are now complete! Programming ON/OFF Times Your screen will now read Dusk at the top with a blinking time below. Your screen will now read DAWN at the top with a blinking time below. Once you've scrolled to the correct time zone for your state, press the OK button once. For example, if you live in Utah, you'll use the dial to scroll to MNTN (Mountain Time). You'll need to select the time zone you live in. Once you've scrolled to the correct location, press the OK button once. For example, if you live in the central area of your state select CTR if you live in the North East corner of your state select NE. Now, you'll need scroll to select approximately where you live in your state. Selected your state by pressing the OK button once. Use the dial to scroll through until you find your state of residence. Your timer is now outfitted to adjust itself for daylight savings. Next, the screen will read OFF, DAYSAV, MONTH, 11 WK 1. Your screen will read ON, DAYSAV, MONTH, 3WK 2. If you do observe daylight savings, select the flashing AUTO by pressing the OK button once. While MAN is flashing, press the OK button once. If you do not observe daylight savings, use the dial to scroll until AUTO is replaced by MAN (Manual). ![]() The screen will read DAYSAV with a flashing AUTO. There are two options here depending on whether or not you observes daylight savings.ġ. Repeat this step to select the correct month and the correct day. Use the dial to scroll to the correct year, then press the OK button once. Scroll through the minutes with the dial and select the desired minutes by pushing the OK button once.Īfter completing the clock, your screen should read 1.1.12.įirst, enter the year. Once you've scrolled to the correct hour, push the OK button once to select.Īfter selecting the hour, the minutes will be flashing. Be mindful of the a.m./p.m in the bottom right corner. To set the hour, turn the round dial and scroll through until you reach the correct hour. Second, you'll setup the ON/OFF program to control the lights.Īfter you've cleared out all the old programs, the clock will flash 12:00 a.m. First, you'll program the time, date, and location. There are two parts to setting up your timer. Once you've successfully reset your low voltage landscape lighting timer to zero, it's time to start programming it. If the date is not showing January 1st 2012, you'll need to try again. Alliance itimer outdoor lighting full#Pro Tip: You'll know whether or not you achieved a full reset when you program the date. If you fail to press and hold down both buttons, you will not achieve a full program wipe. After you've released both buttons, the screen should flash zeros before displaying the clock flashing 12:00 a.m. Hold down both buttons together for 5 seconds. While holding in the small reset button, simultaneously press and hold down the ON/OFF button. Use the point from the paper clip to press in the small button located below the gray OK button on the face of the timer.Ģ. ![]() Take a paperclip and bend it so a point sticking out. You'll want to completely reset your timer to factory settings to ensure that all possible issues are wiped clean from the timer's memory.ġ. The first step to resetting your timer is to completely clear all programs. If you have a different kind of timer, click here to view our other timer tutorial videos. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |